View ACM9070-901-2P-T_7120420.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

july 2013 common mode filters for power line acm series acm4520 [1808 inch]* acm7060 [2824 inch] acm9070 [3628 inch] acm1211 [4844 inch] acm1513 [6052 inch] * dimensions code jis[eia] emc components
(2/15) 001-01 / 20130723 / e9713_acm.fm emc components reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components common mode filters for power line features chip common mode filter for large current applications. for each series, there is excellent common mode impedance and noise suppression in a compact case. acm4520 low profile and small size makes it opt imal for surface mounting. acm7060, 9070, 1211, 1513 compatible with high-density portable devices, which are always being made smaller and lighter, because the height has been red uced. application acm4520 power line noise countermeasure for electronic equipment (dvcs, dvd cams, dscs, etc.). acm7060, 9070, 1211, 1513 power line noise countermeasure for various electronic equipment. noise countermeasure for adapter lines and battery lines or larger electronic equipment such as note book pcs and word processo rs. part number construction operating temperature range, package quantity, product weight the storage temperature range is for after the circuit board is mounted. overview of the acm series acm 4520 - 901 - 2p - t - ??? series name lwh dimensions impedance number of lines packaging style internal code (mm) ( ) at 100mhz 4520 4.52.02.0 901 900 2p 2 lines t ?180mm reel 7060 7.06.03.5 142 1400 tl ?330mm reel 9070 9.07.04.5 1211 12.011.0*6.0 1513 15.013.06.0 type temperature range reel diameter package quantity individual weight operating temperature storage temperature c c mm pieces/reel g acm4520 C40 to +85 C40 to +85 ?180 800 0.15 ?330 2,500 acm7060 C40 to +85 C40 to +85 ?330 1,500 0.35 acm9070 C40 to +85 C40 to +85 ?330 800 0.82 acm1211 C40 to +85 C40 to +85 ?330 500 2.2 acm1513 C40 to +85 C40 to +85 ?330 500 3.15 product compatible with rohs directive halogen-free compatible with lead-free solders rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://www.t dk.co.jp/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components overview of the acm series recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 10 to 30s 245c 5s natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series acm4520 type shape & dimensions recommended land pattern circuit diagram 4.5 4.70.2 4.50.2 2.0max. 0.75 0.75 2.0 0.65 0.65 1 2 4 3 wire ferrite dimensions in mm 1.25 3.5 1.25 0.95 1.05 0.95 2.0 dimensions in mm 1 2 4 3 ? no polarity
(6/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series y acm4520 type electrical characteristics characteristics specification table : includes packaging style indication (t: ?180mm reel, tl: ?330mm reel). measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. common mode impedance ( ) [at 100mhz] dc resistance ( )max. [1 line] rated current (a)max. rated voltage (v)max. insulation resistance (m )min. part no. min. typ. 60c 85c 180 230 0.05 3.0 2.6 50 10 acm4520-231-2p- - ??? 300 420 0.055 2.8 2.4 50 10 acm4520-421-2p- - ??? 650 900 0.06 2.3 2.0 50 10 acm4520-901-2p- - ??? 1000 1400 0.08 1.7 1.5 50 10 acm4520-142-2p- - ??? measurement item product no. manufacturer common mode impedance 4991a agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer 4991a agilent technologies 1 10 100 1000 10000 1000 1 10 100 frequency ( mhz ) impedance ( ) 901 common mode 231 common mode 421 common mode 142 common mode 231 differential mode 901 differential mode 421 differential mode 142 differential mode
(7/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series acm7060 type shape & dimensions recommended land pattern circuit diagram 1.50.2 4.0typ. 1.50.2 1.50.2 1.50.2 1.50.2 3.5max. 7.00.2 6.00.2 1 2 4 3 dimensions in mm 1.51.5 1.5 4.0 2.5 2.5 dimensions in mm 1 2 4 3 ? no polarity
(8/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series y acm7060 type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. common mode impedance ( ) [100mhz] dc resistance (m )max. [1 line] rated current (a)max. insulation resistance (m )min. rated voltage (v)max. part no. min. typ. 225 300 10 5 10 80 acm7060-301-2pl-tl01 500 700 15 4 10 80 acm7060-701-2pl-tl01 measurement item product no. manufacturer common mode impedance 4991a agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer 4991a agilent technologies 1 10 100 1000 10000 1000 1 10 100 frequency ( mhz ) impedance ( ) 301 common mode 701 common mode 301 differential mode 701 differential mode
(9/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series acm9070 type shape & dimensions recommended land pattern circuit diagram 1.50.2 1.50.2 2.00.2 4.5max. 9.00.2 7.00.2 1 2 4 3 1.50.2 6.0typ. 1.50.2 dimensions in mm 2.0 1.5 1.5 6.0 2.5 2.5 dimensions in mm 1 2 4 3 ? no polarity
(10/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series y acm9070 type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. common mode impedance ( ) [100mhz] dc resistance (m )max. [1 line] rated current (a)max. insulation resistance (m )min. rated voltage (v)max. part no. min. typ. 500 700 10 5 10 80 acm9070-701-2pl-tl01 measurement item product no. manufacturer common mode impedance 4991a agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer 4991a agilent technologies 1 10 100 1000 10000 1000 1 10 100 frequency ( mhz ) impedance ( ) 701 common mode 701 differential mode
(11/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series acm1211 type shape & dimensions recommended land pattern circuit diagram 12.00.3 11.00.3 1 2 4 3 2.30.2 7.4typ. 2.30.2 6.0max. 2.70.2 2.70.2 2.50.2 dimensions in mm 2.52.7 2.7 7.6 3.2 3.2 dimensions in mm 1 2 4 3 ? no polarity
(12/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series y acm1211 type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. common mode impedance ( ) [100mhz] dc resistance (m )max. [1 line] rated current (a)max. insulation resistance (m )min. rated voltage (v)max. part no. min. typ. 500 700 6 8 10 80 acm1211-701-2pl-tl01 750 1000 14 6 10 80 acm1211-102-2pl-tl01 measurement item product no. manufacturer common mode impedance 4991a agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer 4991a agilent technologies 1 10 100 1000 10000 1000 1 10 100 frequency ( mhz ) impedance ( ) 701 common mode 102 common mode 701 differential mode 102 differential mode
(13/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series acm1513 type shape & dimensions recommended land pattern circuit diagram 2.30.2 10.4typ. 2.30.2 15.00.5 3.80.2 2.70.2 2.70.2 13.00.4 1 2 4 3 6.0max. dimensions in mm 3.82.7 2.7 10.4 3.3 3.3 dimensions in mm 1 2 4 3 ? no polarity
(14/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series y acm1513 type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. common mode impedance ( ) [100mhz] dc resistance (m )max. [1 line] rated current (a)max. insulation resistance (m )min. rated voltage (v)max. part no. min. typ. 450 550 4 10 10 50 acm1513-551-2pl-tlhf measurement item product no. manufacturer common mode impedance 4991a agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer 4991a agilent technologies 1 10 100 1000 10000 1000 10 100 frequency ( mhz ) impedance ( ) 701 common mode 701 differential mode
(15/15) 001-01 / 20130723 / e9713_acm.fm ? all specifications are subject to change without notice. emc components acm series packaging style reel dimensions tape dimensions ty p e a w1 w2 n e acm4520 ?3302 13.50.5 17.51 1001 2 typ. ?1803 130.3 171.4 60+1/C0 2 typ. acm7060 ?3302 16.4+2/C0 20.4 typ. 1001 2 typ. acm9070 ?3302 16.4+2/C0 20.4 typ. 1001 2 typ. acm1211 ?3302 24.4+2/C0 28.4 typ. 1001 2 typ. acm1513 ?3302 24.4+2/C0 28.4 typ. 1001 2 typ. dimensions in mm ty p e a b ?d0 e f p0 p1 p2 w k t acm4520 4.750.1 5.050.1 1.55+0.1/0 1.750.1 5.50.05 4.00.1 8.00.1 2.00.05 12.00.2 2.050.05 0.30.1 acm7060 6.60.1 7.60.1 1.5+0.1/0 1.750.1 7.50.1 4.00.1 8.00.1 2.00.1 16.00.3 3.60.1 0.40.05 acm9070 7.60.1 9.60.1 1.5+0.1/0 1.750.1 7.50.1 4.00.1 12.00.1 2.00.1 16.00.3 4.60.1 0.40.05 acm1211 11.50.1 12.50.1 1.5+0.1/0 1.750.1 11.50.1 4.00.1 16.00.1 2.00.1 24.00.3 6.40.1 0.50.05 acm1513 13.40.1 15.50.1 1.5+0.1/0 1.750.1 11.50.1 4.00.1 16.00.1 2.00.1 24.0+0.3/C0.1 7.30.1 0.40.05 ?13.0 0.2 ?21.0 0.8 n e 2.0 0.5 a dimensions in mm 1.0 w2 w1 b fe w p0 p2 p1 a ?d0 t k 160min. taping 440min. drawing direction 500 to 560min. dimensions in mm

▲Up To Search▲

Price & Availability of ACM9070-901-2P-T

	To Download ACM9070-901-2P-T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .